The project toolbox

Roof Pitch Calculator

Convert rise and run, degrees, or an X/12 pitch into the measurements you need for roof planning. Homeowners and tradespeople can compare slope, check a rafter length, and explore common material considerations.

Project dimensions

LIVE ESTIMATE
Use the same unit as run.
Horizontal distance, not roof length.
Greater than or equal to 0, below 90.
Inches of rise per 12 inches of run.

Choose which measurement to edit. The other representations stay in sync.

Rafter result excludes overhangs and cuts.

Your project estimate

Live estimateView results ↑

Understanding the roof results

Pitch expresses rise per 12 units of horizontal run. The angle shows the same slope in degrees, while slope percent is rise divided by run, times 100. The multiplier converts horizontal distance to distance along the roof.

The category is a planning label: below 2/12 is low slope, 2/12 to below 4/12 is a transitional low pitch, 4/12 through 9/12 is standard, and above 9/12 is steep. These labels do not certify that a product or structural design is suitable.

How to use the roof pitch calculator

These steps show how to calculate roof pitch from the measurements you already have.

  1. Select rise and run, angle, or pitch as your starting measurement.
  2. Enter the known values; rise and run must share the same unit.
  3. Enter the horizontal rafter run in feet to estimate slope length.
  4. Review the diagram, compare the chart, and verify roofing requirements with the product manufacturer.

Roof pitch formula and worked example

Ratio = rise ÷ run
Pitch = (12 × ratio) / 12
Angle = atan(ratio) × 180 ÷ π
Slope (%) = ratio × 100
Multiplier = √(1 + ratio²)
Rafter length = horizontal run × multiplier

With a rise of 6 and run of 12, the ratio is 0.5 and the pitch is 6/12. The angle is 26.57°, the slope is 50%, and the multiplier is 1.118. A 12 ft horizontal run gives a rafter length of 13.42 ft before overhangs or framing adjustments.

Practical roof planning tips

Roof pitch chart: 1/12 through 12/12

Roof pitch reference: rise per 12 units of horizontal run
PitchAngleMultiplier
1/124.76°1.003
2/129.46°1.014
3/1214.04°1.031
4/1218.43°1.054
5/1222.62°1.083
6/1226.57°1.118
7/1230.26°1.158
8/1233.69°1.202
9/1236.87°1.250
10/1239.81°1.302
11/1242.51°1.357
12/1245.00°1.414

Frequently asked questions

How do I figure roof pitch from rise and run?

Divide vertical rise by horizontal run, then multiply by 12. A 6 inch rise over a 12 inch run is a 6/12 pitch. Use matching units for both measurements.

Is a 6/12 pitch the same as 6 degrees?

No. A 6/12 pitch has a rise-to-run ratio of 0.5 and an angle of about 26.57 degrees. Pitch and degrees describe the same slope in different ways.

What is a suitable shed roof pitch?

A shed roof pitch depends on the roofing system, climate, drainage, and local requirements. Check the exact product instructions. Low slopes often require a membrane or a roofing system designed for low-slope installation.

Does rafter length include overhang?

No. The result is the geometric slope length for your horizontal run. Add any required overhang and account for ridge details and seat cuts in a proper framing plan.

Which materials suit a low-slope roof?

Purpose-designed membrane systems can suit low slopes. Asphalt shingles commonly require at least 2/12, with special underlayment at lower permitted pitches. Metal minimums vary by panel and seam system; always check the manufacturer.

Can I measure roof pitch safely from inside?

You can sometimes measure rise and run against an accessible rafter in an attic, provided access is safe. Avoid climbing onto a roof to obtain a planning measurement. A roofing professional can confirm uncertain dimensions.

How do I figure roof pitch?

Measure the vertical rise over a 12-inch horizontal run; the rise in inches gives the X in an X/12 pitch. You can also enter your measured rise and run in the calculator above, using matching units.

Related calculators

Floors, walls & backsplashes

Tile Calculator

Turn room dimensions into a tile count, box quantity, and budget—with grout spacing and waste included.

Open calculator
Slabs, footings & posts

Concrete Calculator

Find cubic yards, cubic meters, and bag quantities for your next pour, with an allowance for waste.

Open calculator